Skip to main content

Raspberry Pi - Voice Recording & Text-to-Speech

Raspberry Pi,

This tutorial is about the Voice Recording and Test to speech Using Raspberry Pi. But First, let's have a small introduction about Raspberry Pi.

Introduction
Raspberry Pi 3 Model B



System on Chip(SoC)
  • What is System on Chip?
                - A complex IC that integrates the major functional elements into a single chip or chipset.
  • Programmable processors
  • On-chip memory
  • Accelerating function hardware (e.g. GPU)
  • Both hardware and Software
  • Analog components
  • Benefits of SoC
                  - Reduce overall system cost
                  - Increase performance
                  - Lower power consumption
                  - Reduce size

Soc in Raspberry Pi: Broadcom BCCM2835 SoC Multimedia Processor
  • CPU
            - ARM 1176JZF-S (armv6k) 700MHz
            - RISC Architecture and low power draw
            - Not compatible with traditional PC software
  • GPU
            - Broadcom Video IV
            - Specialized graphical instruction sets
  • RAM
            - 512MB (Model B rev.2)
            - 256MB (Model A, Model B rev.1)

Labeled Diagram of Raspberry Pi

Voice Recording AndText-to-speech using R-Pi

Component Required:
  • Rasberry Pi 3 Model-B
  • Adapter Charger micro USB-b Type 5v,2Amp
  • Sound Card
  • Mic
  • Speaker

Connection Diagram:


For more watch video.

Step1: Checking Your Microphone

You need to first check whether your microphone record properly or not. Check microphone is listed or not by using command "lsusb". Next, we need to set the mic recording volume high by using command "alsamixer". Now, you need to check if the recording takes place properly by using command "arecord -l".

Step2: Recording Your Voice

To record your voice use command "arecord -D plughw:1,0 test.wav". Record your voice message and to terminate recording press Ctrl+Z.

Step3: Play Your Recording

To play your recording use command "aplay test.wav".

Text-to-speech

To give R-pi a voice we must first install some software called eSpeak.
Install eSpeak by using the following command:

Sudo apt-get install espeak

After installing the eSpeak r-pi is ready. Now, by the following command you can give Text-to-speech command to your r-pi.

espeak “Hello World! My name is Raspberry Pi” > /dev/null

Press enter.

For more, you can watch our Video.


Thinking?
 Join our hands-on training courses.
 To know more visit us at Karkhana Training Portal

Comments

Popular posts from this blog

IoT - LPG Gas Sensor Logging with NodeMCU and Thingspeak.

In this tutorial, will learn, how to interface MQ-5 Module with Node Mcu(ESP8266).

The Grove - Gas Sensor(MQ5) module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer.


Components Required
NodeMcu(ESP8266) MQ-5 LPG SENSOR Module Few male to female connecting wires Breadboard  Follow the image below for circuit connection reference:-
After making the circuit dump the code given below:-

// Karkhana Report
// Analyse the volume of the gas using thingspeak.com
// Hardware: NodeMCU,MQ-5

#include <ESP8266WiFi.h>
String apiKey = "Enter the API key"; // Enter your Write API key from ThingSpeak
const char *ssid = "Enter ssid"; // replace with your wifi ssid and wpa2 key
const char *pass = "Enter password";
const char* server = &qu…

IoT - Humidity and Temperature Logging using NodeMCU and ThingSpeak

Hey Folks,
In this tutorial, we will learn, how to interface DHT 11 with Node Mcu(ESP8266).
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).




Components Required
NodeMcu(ESP8266) DHT 11 SENSOR Few male to female connecting wires Breadboard
Follow the image below for circuit connection reference.
In this circuit, we have connected the output pin to the D3 pin of the NodeMcu module and NC pin remain disconnected. After making the circuit dump the code given below.
// Karkhana Report
// temperature and humidity data using thingspeak.com
// Hardware: NodeMCU,DHT11
#include <DHT.h> // Including library for dht
#include <ESP8266WiFi.h>
String apiKey = "THINGSPEAK API KEY"; // Enter your Write API key from ThingSpeak
const char *ssid = "ENTER YOUR SSID"; // replace with your wifi ssid a…

Getting Started with Embedded System Design on AVR

In this tutorial, we will learn how to interface LED with Atmega16 using AVR Studio.
An embedded system is built around a processor. The design goals of an embedded system are to reduce size, cost and power consumption and to increase performance and reliability.
The microprocessor we are using is ATMEGA16. The processor has limited internal memory, and if this is not sufficient for a given application external memory devices are used. The hardware also includes any components that facilitate the user-application interaction such as display units, keypad. The light emitting diodes are used for getting status information, such as power on, check output(high/low). You all must have observed led decoration lights, which can glow in different patterns.
First, we will learn to interface a single Led and then 8 LEDs to learn a simple toggling technique.
Components Required:- AVR controller(Atmega16)LEDsConnecting wiresUSBASP Programmer For single Led dump the following code:
#include<avr/io.h> #in…